Ford Sierra Manual

Ignition timing (OHC models) - adjustment
Engine electrical systems / Ignition timing (OHC models) - adjustment


Note: During production the ignition timing is accurately set using a microwave process, and sealant is applied to the distributor clamp bolt. Because the electronic components require no maintenance, checking the ignition timing does not constitute part of the routine maintenance schedule, and the procedure is therefore only necessary after removal and refitting of the distributor. A timing light will be required for this procedure. For details of ignition timing adjustment in order to operate vehicles on unleaded petrol refer to the appropriate Section of this Chapter.

All models except 2.0 litre DOHC 1 Before checking the ignition timing, the following conditions must be met: a) The engine must be at normal operating temperature
b) Where applicable, the vacuum pipe to the distributor vacuum unit or electronic module (as applicable) must be disconnected from the vacuum unit or electronic module and plugged c) The idle speed must be below 900 rpm (isolate idle speed adjustment wire if necessary)
d) Any earthed octane adjustment wires must be temporarily isolated 2 Wipe clean the crankshaft pulley timing marks and the pointer on the crankshaft front oil seal housing. Note that two alternative types of pulley may be fitted (see illustration).

16.2a Highlighted timing marks - SOHC engine with cast crankshaft pulley
16.2a Highlighted timing marks - SOHC engine with cast crankshaft pulley

The desired timing values are given in the Specifications. If necessary, use white paint or chalk to highlight the relevant timing mark(s) (see illustration).

16.2b Crankshaft pulley timing marks - SOHC engine
16.2b Crankshaft pulley timing marks - SOHC engine

A Cast pulley B Pressed steel pulley

3 Connect a stroboscope timing light to the No 1 cylinder HT lead, following the manufacturers instructions.

4 With the engine idling at normal operating temperature, point the timing light at the marks on the crankshaft pulley, and check that the appropriate timing mark appears stationary in line with the timing cover pointer.

Take care not to get the timing light leads, clothing etc tangled in the cooling fan blades or other moving parts of the engine.

5 If adjustment is necessary, stop the engine, slacken the distributor clamp bolt, and turn the distributor body slightly. Turn the distributor body clockwise to retard the ignition timing (move the timing closer to TDC) and anti-clockwise to advance the timing.

Note that the required distributor body movement will be half of the required crankshaft movement (ie an adjustment of 5 in ignition timing will require the distributor body to be turned 2º. Tighten the clamp bolt and re-check the timing.

6 On models with inductive discharge ignition systems, the mechanical and vacuum advance mechanisms can be checked as follows. On all other models, proceed to paragraph 10.

7 With the engine idling, timing light connected, and vacuum pipe disconnected as described in the preceding paragraphs, increase the engine speed to approximately 2000 rpm (if desired, connect a tachometer to the engine in accordance with the manufacturers instructions). Note the approximate distance which the relevant pulley mark moves out of alignment with the pointer.

8 Reconnect the vacuum pipe to the distributor or electronic module, as applicable, and repeat the procedure given in the previous paragraph, when for the same increase in engine speed, the alignment differential between the pulley mark and pointer should be greater than previously observed.

9 If the pulley mark does not appear to move during the first part of the check, a fault in the distributor mechanical advance mechanism is indicated. No increased movement of the mark during the second part of the check indicates a punctured diaphragm in the distributor vacuum unit, or a leak in the vacuum line.

10 On completion of the adjustments and checks, stop the engine and disconnect the timing light. Where applicable, reconnect the vacuum pipe, if not already done, and reconnect any octane adjustment and idle speed adjustment wires. Make a final check to ensure that the distributor clamp bolt is tight.

11 Finally, the idle speed and mixture should be checked and adjusted.

2.0 litre DOHC carburettor model 12 The ignition timing is controlled by the ESC II module, and no adjustment is possible.

2.0 litre DOHC fuel injection model
13 The ignition timing is controlled by the EEC IV module, and no adjustment is possible.


2018 www.fsierra.ru. All Rights Reserved.